For most of thirty years I carried one pair of needle-nose pliers in the bottom of my tackle box. The jaws were sprung, the hinge was rusted, and I used them for everything: unhooking bluegill, crimping split shot, and once, badly, sawing through 20-pound braid with the wire cutter near the hinge. I thought that was just what pliers were. Then a friend handed me a pair of Booms Fishing X1 pliers on the pier at South Haven one October morning, and for the rest of that trip I kept noticing small fumbles I had been calling normal.
What follows is not a spec sheet read aloud. These are ten specific moments from my own boat, a 14-foot aluminum jon boat with a trolling motor that sticks in second speed, and from the shore and the piers where I fish in southwest Michigan. I work small inland lakes for bass, bluegill and crappie, a nearby river for smallmouth, and the big lake in spring and fall when the wind lets me. My grandson Tyler, who is twelve, comes along on some summer weekends and has already lost two pairs of cheap pliers over the side. So I have opinions about what belongs on a belt.
Ten small fumbles you stop having
The Booms Fishing X1 is the pair clipped to my vest now. Stainless steel jaws, aluminum handle with an inset spring, coiled lanyard and a sheath that stays where you put it.
Amazon Check Today's Price on Amazon →Opens a stubborn split ring without taking a fingernail with it
There is a small hook at the top of the jaws made for exactly one job: prying open a split ring. I used to do that with my thumbnail, which works right up until the ring snaps back and takes a piece of you with it. On a size 5 spinnerbait the hook slides in, the ring opens, and you swap the blade or the hook in about the time it used to take me to find my glasses. It is a small thing built into the jaw and it is the feature I reach for most.
Cuts braided line flush on the first squeeze
Braid does not cut with a pair of dull side cutters. It frays, it squirms, and you end up with a fuzzy tag you have to trim twice. The line cutters on these are set into the aluminum handle, and the first squeeze on 20-pound braid leaves a clean end. I retie more often now, which sounds like a chore and is actually the reason I have lost fewer fish this season than last.
Gets a swallowed hook out without gilling the fish
When a bluegill takes a hook deep, the long stainless jaws reach in past the teeth where my fingers will not go. You get hold of the hook shank and roll it out. I still keep a proper hook-out in the box for the bad ones, but on nine out of ten fish these are what I pick up first, and the fish go back in the water swimming instead of floating.
Crimps a split shot so it stays where you put it
I run a split shot above a small jig on the river for smallmouth, and I have watched plenty of them slide down the line because I pinched them with the wrong tool. The jaw has a flat spot for crimping. Two firm squeezes and the shot stays put through a whole morning of casting. It is not exciting work, but it is the difference between fishing the depth you want and fishing the depth you ended up with.
Keeps one tool on your belt instead of three in your pockets
Before this I carried needle-nose, a separate cutter, and a hook-out, and I could never find the one I wanted with a fish in my hand. One pair does all of it. The Booms sheath rides on the belt and the coiled lanyard means that when I fumble it over the side, which I have, it comes back up instead of joining the two pairs Tyler lost.
The little hook at the top of the jaws popped a split ring open in about two seconds, and I did not lose a fingernail doing it.
Light enough on the belt that you forget it is there
The whole thing comes in at 0.19 kg on the spec sheet. That is light enough to hang on the belt all day without pulling my waders down, and light enough that Tyler can use it without complaining. Aluminum handle, stainless steel jaws and other parts, and it does not feel like a toy in the hand.
Stainless jaws survive a season of pier spray
The piers at South Haven in the fall will rust anything you leave sitting in the bucket. The jaws and the other metal parts are stainless steel, and after a full season of that, with a rinse at the end of the day and nothing else, mine still open and close clean. I have thrown away pliers that seized up by August. These have not.
The inset spring lets you work one-handed
The spring sits inside the aluminum handle, so the jaws open back up on their own after every squeeze. That sounds minor until you are holding a thrashing smallmouth against the gunwale with one hand and need the pliers ready with the other. Pliers that need two hands to open are pliers you put down in the bottom of the boat.
Smooth aluminum handle wipes clean in one pass
I am not fussy about gear, but a handle with a lot of grooves in it will hold slime and scales until it smells like the bottom of the livewell. The grip here is smooth aluminum. A wipe on your jeans and it is done. It is slick when your hands are wet, which is the trade-off I get to below, but it cleans up in a second and that matters more to me than texture.
Does the four jobs I actually have, and nothing else
The listing is honest about what it is for: opening split rings, removing hooks, cutting braided line, crimping. That is my entire season in four jobs. It is not a screwdriver, it is not a bottle opener, and it does not pretend to be a fillet knife. A tool that does four things well beats a tool that does twelve things badly, and the Booms X1 has stayed in the sheath while the twelve job gadget is somewhere out in the garage.
What I'd Skip
Two honest complaints. First, the smooth aluminum grip is slick when your hands are covered in slime and it is forty degrees on the pier. I have not dropped it, thanks to the lanyard, but I have come close, and if I fished bare-handed in cold rain every week I would want something with more texture on it.
Second, the Booms X1 is not the tool for a deeply hooked fish where the point is past the bend. The jaws are strong but they are not fine, and on a small bluegill hooked in the throat you want a proper hook-out with a long thin reach. I keep one in the box for that. Also, the cutters are for line. Do not go at a hook shank with them and expect the edge to survive the season.
If your pliers live in the bottom of the box, this is the upgrade
The Booms Fishing X1 covers four jobs with one tool, a sheath, and a lanyard that brings it back. Rated 4.6 across 2,846 reviews on Amazon. Mine has been on the belt since spring.
Amazon Check Today's Price on Amazon →