The worst ten minutes of any fishing trip used to happen after the fish was already in the boat. A bluegill takes a hook past the bend, the fish starts flopping on the bench, my glasses fog up, and I am rooting around the bottom of the tackle box for a pair of needle-nose pliers that have been riding in there since the 1990s. The jaws are pitted. The spring gave out years ago. By the time I get the hook backed out, the fish is worn out and so am I, and about one trip in five I end up with the hook in my own thumb instead.

Last June I had a Saturday that broke it. I lost a crankbait to a snag on a lake west of Kalamazoo, then spent four minutes working a hook out of a largemouth with those same needle-nose pliers while the fish thrashed and the line wrapped around my wrist. That night I ordered the Booms Fishing X1 pliers. It is 0.19 kilograms of aluminum and stainless steel, and it has saved me more aggravation in one season than any rod I have bought in the last five years.

A hand holding fishing pliers above a boat bench while working a hook free of a fishing line

What showed up was simpler than I expected. Aluminum handles with the spring inset into the handle instead of dangling loose where it snaps. Stainless steel jaws and hardware, which matters on the Lake Michigan piers at South Haven where the spray eats cheap tools alive. A coiled lanyard and a sheath, so the pliers are on the boat or on my belt and not at the bottom of a bag. The grip is smooth aluminum with no rubber sleeve to peel off in two seasons, and the whole tool is listed at 0.19 kilograms.

The part that actually changed my fishing is the jaws. There is a small hook at the top of them, and that hook opens a stubborn split ring without me digging out a second tool. I swap treble hooks on crankbaits more than I should, and I have pinched fingers doing it for twenty years. The braided line cutters are inset in the handle, so I trim braid or mono without reaching for a clipper. One tool on the bench instead of three, and nothing else to lose over the side.

The small hook at the top of the jaws opens a stubborn split ring in one motion. I did not know I was missing it, and now I use it every trip.

One tool on the boat bench instead of three at the bottom of the bag

The Booms Fishing X1 pairs aluminum handles with stainless steel jaws, an inset braided line cutter, a split ring hook at the top of the jaws, a coiled lanyard and a sheath. It is rated 4.6 out of 5 across 2,846 reviews. Today's price is on the listing.

Check Today's Price on Amazon →

A full season later the Booms Fishing X1 still opens smooth. I rinse it in fresh water and dry it on a rag, and that is the whole maintenance routine. The inset spring has not gone soft. The jaws have not pitted the way my old pair did. I have cut 30-pound braid with the inset cutter more times than I can count and the tag ends come out clean instead of frayed. There are a couple of scratches on the aluminum from the boat bench, which I count as normal wear on a tool that lives in a wet environment.

A boy and an older angler on a wooden dock at a small lake with a landing net resting beside them

Two things I would change. The smooth aluminum grip gets slick once your hands are covered in lake water and fish slime, and I fumbled it once on a hot afternoon. The coiled lanyard is the only reason it is still mine. The other is that the cutters sit inside the handle, so you line the line up in the slot rather than snipping at whatever angle you happen to be holding. That is a two-second adjustment once you have done it a few times, but it is not instant on the first trip.

My grandson Tyler is twelve and rides along on summer weekends. In July he hooked a crappie that had taken the hook deep, and instead of doing it for him I handed him the pliers. He had it out on the second try and the fish went back in the livewell clean. That is the part of this I care about most. A kid who learns to unhook a fish quickly and without mangling it is a kid who will still be fishing when he is my age.

On the river I keep the pliers on the coiled lanyard around my wrist. When a smallmouth buries a hook in the corner of its jaw, the stainless jaws get hold of the shank without crushing the hook point, and the hook at the top of the jaws handles the trebles when I want to swap one out on a rock pile. I fish from a fourteen foot aluminum jon boat or from the bank, and this is the one piece of tackle I have bought since retiring that I reach for on every single trip.

What I'd Tell You If We Were Sitting at My Kitchen Table

If you are still carrying needle-nose pliers in a tackle box, you are making the hardest part of the day harder than it needs to be. You do not need a box full of tools. You need one pair that cuts line, opens a split ring, and gets a hook out of a fish without you holding a flashlight in your teeth. Buy the pliers before you buy another lure. The Booms Fishing X1 is the one I would slide across the table to you. Rinse it at the end of the day, keep it on the lanyard so it does not go over the side, and let a kid use it. That is the whole advice. The rest is just time on the water.

Get the hook out, cut the line, and get back to fishing

Aluminum handles, stainless steel jaws, inset braided line cutters, a split ring hook, a coiled lanyard and a sheath. Check the current listing for today's price and shipping.

Check Today's Price on Amazon →